How to Configure a Cisco Catalyst 2960 Switch/Layer 2 Switch?

On the off chance that you are hoping to improve your network execution by supplanting your old network hubs, and need execution and unwavering quality alongside passage level QoS (Quality of Service) and PoE (Power over Ethernet), at that point the Cisco 2960 switch ought to be your top decision. In the event that you have just had a 2960, at that point you would attempt to improve your system execution and manageability. The Cisco Catalyst 2960 comes in a few models, with 8, 24 or 48 ports, supporting Fast Ethernet and Gigabit Ethernet. The 2960 switch is an ideal gadget for an independent company or a branch office area.

Things You Require for Configuration of Cisco 2960 Layer 2 Switch

Here are the things which you need for configuration of Cisco 2960 switch to layer 2:

Telnet password
IP address
Computer with terminal emulation software
Enable password
Serial cable
Subnet mask
Enable secret password

How to Configure Cisco 2960 Switch?

Below are the important steps, which you need to follow in order to successfully configure Cisco 2960 switch to layer 2:

Connect the switch to your PC with the blue serial cable that ought to have been incorporated with the switch. Connect the RJ-45 end of the cable to the switch. This is the end that looks like a huge phone connector. Connect the 9-pin d-shell end of the cable to your PC’s serial port.
Power on your PC and configure and set up a terminal meeting to the switch. You can utilize any product that gives terminal emulation, and there are a few free projects accessible on the Internet, including CRT, Putty and HyperTerminal. Set the terminal meeting boundaries to Xon/Xoff flow control, 9600 baud, 8 information bits, 1 stop bit and no equality.
Power on the switch and search for the startup messages. Check your terminal meeting settings in the event that you don’t see the messages following a moment or somewhere in the vicinity. Be certain the terminal meeting settings are right.
Proceed to the underlying configuration dialog and fundamental management setup by accepting the defaults of “yes” at the prompts. You can acknowledge the defaults by simply pressing “Enter.”
Press “Enter” when incited for the host name to accept the default of “Switch,” or enter an alternate host name and press “Enter.”
Enter the enable secret password, and press “Enter.” Repeat this procedure for the enable password and the virtual terminal secret phrase. Make certain to record each of the three passwords and store them in a protected spot.
In the event that you are incited about SNMP Network Management acknowledge the default by pressing “Enter.” Enter “vlan1” and press “Enter.” This will recognize the interface that will be utilized to associate with the management network.
Enter “yes” when prompted to “Configure IP on this interface?” and press “Enter.” Enter the IP address for the switch and press “Enter.” Enter the subnet mask at the prompt and press “Enter.”
Enter “no” whenever prompted to “enable as a bunch command switch,” and press “Enter.” The switch will presently show the current configuration, and you will be given three choices.
Enter “2” and press “Enter” to save the configuration to NVRAM and exit. At the point when the switch comes back with its prompt, you are done with the initial configuration for your Cisco 2960 switch.

In the event that you need a Cisco Access Switch that can create with your business, will be dynamically secure, be less erratic, be progressively shrewd, it must be Cisco 2960 X series. The Cisco2960-X and XR series switches join plans for any undertaking network. They are stacked Gigabit Ethernet Layer 2 and Layer 3 access switches to improve deployment, trouble shooting, and management. This switch not just backings automated software installation and port configuration yet adjacent to other vitality sparing features to help you with reducing costs.

The Catalyst 2960 series is furthermore built in for network programmability. The new switches are Cisco onePK-arranged – Cisco onePK is an easy to-use Cisco Software-Defined Networking (SDN) tool stash for advancement, automation and speedy help creation. In light of being onePK-arranged, the Catalyst 2960 series switches enable customers to manufacture applications to motorize and make administration over the campus, further extending the endeavor security capacities of this new switch series by Cisco.

The Cisco Catalyst 2960 presents another first for the Catalyst 2K family: Layer 3 steering limit nearby application-careful knowledge, reasonably making it the “sharpest” switches in its family families. Cisco 2960-X arrangement switches are anything but difficult to send, administer and explore. As a significant part of Cisco’s Unified Access portfolio, the Cisco 2960 series switches are moreover totally joined with Cisco Prime for direct action from a central zone and Cisco Identity Services Engine (ISE) for improved One Policy the officials. The switches can in like manner be regulated by Cisco Network Assistant (CNA), which incorporates an instinctual GUI to allow customers to viably apply fundamental organizations across Cisco routers, switches and access points.

kevinmartez